Xilinx ML507 Manual do Utilizador

ML507 QuickStartMay 2008

Bootload• The bootload_video.ace loads:Note: Presentation applies to the ML507

Bootload• The terminal window also reflects the bootload application• Use the left/center/right buttons to choose an application or type a number in t

Slideshow• Type 1, to launch the slideshow application in Configuration 1• The slideshow loads the presentation into memory then presents itNote: Pres

Slideshow• The slideshow app will present a series of slides on the Monitor:Note: Presentation applies to the ML507

Web Server• Type 2, to launch the web server application in Configuration 2– Note: You may need to turn off your browser's proxy and specify a di

Running the LWIP Demo• Open a web browser to address 192.168.1.10

Running the LWIP Demo• Click the Toggle LEDs button; view change on ML507

Simon• Type 3, to launch the Simon application in Configuration 3Note: Presentation applies to the ML507

Board Diagnostics• Type 4, to launch the XROM application in Configuration 4Note: Presentation applies to the ML507

Board Diagnostics• XROM includes a series of board test routinesNote: Presentation applies to the ML507

Overview• Setup• Boot with ACE-loader ACE File• Observe LCD and Terminal messages • Load new Configuration• Re-load ACE-loader

USB Keyboard• Type 5, to launch the USB Keyboard application in Configuration 5• Type ML507 and view results:Note: Attach keyboard after demo loads

My ACE• Type 6, to launch the My ACE application in Configuration 6Note: Presentation applies to the ML507

Ringtone• Type 7, to launch the Ringtone application in Configuration 7• Press any key then press 1-7 to play a simple melodyNote: Presentation applie

Documentation• Virtex-5– Silicon Deviceshttp://www.xilinx.com/products/silicon_solutions– Virtex-5 Multi-Platform FPGAhttp://www.xilinx.com/products/s

Documentation• Virtex-5 – Virtex-5 FPGA User Guidehttp://www.xilinx.com/support/documentation/user_guides/ug190.pdf– Virtex-5 FPGA Configuration User

Documentation• Virtex-5 RocketIO– RocketIO GTP Transceivershttp://www.xilinx.com/products/silicon_solutions/fpgas/virtex/virtex5/capabilities/RocketIO

Documentation• Design Resources– ISE Development Tools and IPhttp://www.xilinx.com/ise– Integrated Software Environment (ISE) Foundation Resourceshttp

Documentation• Additional Design Resources– Customer Supporthttp://www.xilinx.com/support– Xilinx Design Services: http://www.xilinx.com/xds– Titanium

Documentation• Platform Studio– Embedded Development Kit (EDK) Resourceshttp://www.xilinx.com/edk– Embedded System Tools Reference Manualhttp://www.xi

Documentation• MicroBlaze– MicroBlaze Processorhttp://www.xilinx.com/microblaze– MicroBlaze Processor Reference Guide – UG081http://www.xilinx.com/sup

ML507 BSB Hardware• The ML507 PPC440 design hardware includes:– PPC440MC DDR2 Interface– External Memory Controller (EMC)• ZBT SRAM– BRAM – Networking

Documentation• Memory Solutions– Demos on Demand – Memory Interface Solutions with Xilinx FPGAs http://www.demosondemand.com/clients/xilinx/001/page_n

Documentation• Ethernet– Virtex-5 Embedded Tri-Mode Ethernet MAC Wrapper Data Sheethttp://www.xilinx.com/support/documentation/ip_documentation/v5_ema

Documentation• ML505/506/507– ML505 Overviewhttp://www.xilinx.com/ml505– ML506 Overviewhttp://www.xilinx.com/ml506– ML507 Overviewhttp://www.xilinx.co

Documentation• ML505/506/507– ML505/506/507 Schematicshttp://www.xilinx.com/support/documentation/boards_and_kits/ml50x_schematics.pdf– ML505/506/507

Additional Setup Details• Refer to ml505_overview_setup document for details on:– Software Requirements– ML507 Board Setup• Equipment and Cables• Soft

Hardware Setup• Connect the Xilinx Parallel Cable IV (PC4) to the ML507 board• Connect the RS232 nullmodem cable to the ML507 boardNote: Presentation

Hardware Setup• The ML507 uses a DVI videointerface• Connect a DVI monitoror• Use a DVI/VGA adapter to connect a VGA monitor– http://www.belkin.comNot

Hardware Setup• USB Keyboard– www.dell.comNote: Presentation applies to the ML507

Factory CompactFlash• The CompactFlash shipped with the ML507 board has the following ace files preloaded:Note: Presentation applies to the ML507

Verify Factory Default Settings• Set the Ethernet PHY jumpers, J22, J23 to positions 1-2 (1)• Insert the Factory CompactFlash into the ML507 board (2)